[V4.2.9.2]
	1. Fixed scutum. Unable to connect by bssid in 10.9.

[V4.2.9.1]
	1. Fixed the free wrong size memory in MlmeFreeMemoryHandler(), it will cause kernel panic in 10.9.

[V4.2.9.0]
	1. New Add pid&vid for Zyxel USB\Vid_0586&Pid_3421

[V4.2.8.0]
	1. New Add pid&vid for ALPHA USB\Vid_2001&Pid_3C20
	2. New Add pid&vid for ALPHA USB\Vid_07D1&Pid_3C15
	3. New Add pid&vid for ALPHA USB\Vid_2001&Pid_3C21
	4. New Add pid&vid for ALPHA USB\Vid_2001&Pid_3C23
	5. New Add pid&vid for ALPHA USB\Vid_2001&Pid_3C24

[V4.2.7.1]
	1. New Add SiteCom VID_0DF6/PID_006E

[V4.2.7.0] 2012-10-18
	1. For RT3573: Disable HW_GPIO checking Radio On/Off
	2. For RT3573: Set VCO to middle
	3. New Add WNC VID_13B1/PID_003B
	
[V.4.2.6.0]
	1. 5G band cant scan AP after radio on/off.

[V.4.2.5.0]
	1. Re-modify 4.2.4.0.
	
[V.4.2.4.0]
	1. Changed Sitecoms RT3573 from 3x3 to 2x3.

[V.4.2.3.0]
	1. Fixed 5370G PPAD of Aux Antenna problem.

[V.4.2.2.0]
	1.	Fixed WEP 128 bit connection problem.
	2.	Enhanced auto co-work for 32/64 bit driver with 32/64bit UI.

[V.4.2.1.0]
	1.	32Bits Driver supported 64Bits Preferecne Panel UI..

[V.4.2.0.0]
	1.	Tuned scan time.

[V.4.1.5.0]
1.	Remove some setting in message function.

[V.4.1.5.0]
1.	Remove some setting in message function.

[V.4.1.4.0]
1.	Fixed WPA2-PSK/AES/TKIP connection problem on MAC OS 10.4.

[V.4.1.3.0]
1.	Fixed crash caused by spin lock deadlock.
2.	Fixed remove key too late when connect to WPA2-PSK/AES AP.

[V.4.1.2.0]
1.	Fixed RT3572 with HW PBCs GPIO problem. Register wrote wrong value.

[V.4.1.1.0]
1.	Fixed crashed problem when setting WDS type in mbuf.

[V.4.1.0.0]
1.	Supported RT5370.

[V.4.1.0.0]
1.	Supported RT3573.

[V.4.0.0.0]
1.	Supported SoftAp.

[V.3.0.3.0]
1.	Fixed WPA-PSK/WPA2-PSK Handshake function fro group key.
2.	Fixed Scutum cant connect when reboot.

[V.3.0.2.0]
1.	Fixed WPS LED MODE 8 when turn off Radio.
2.	Fixed group key hasdshake when rekey problem of TKIP.

[V.3.0.1.0]
1. Added VCO calibration.

	
[V 1.1.1.0] 2008-06-02
	1. Sync with VSS
	2. Resolved connection problem with DIR-300. Changed location of preparing IE of WPA-PSK/WPA2-PSK.

[V 1.0.0.0] 2007-03-29
	for intel MBP, remove unnecessary SimpleLocks
	release verison

[V 1.0.0.0] - RC1
	first release version

[V 0.0.1.e3]
	seems solve the sleep and wakeup panic issue.
	solve RT2890 on MacBookPro driver not release issue.
		return kIOReturnSuccess for message(kIOMessageServiceIsTerminated, ...)

[V 0.0.1.e2]
	longer the sleep time (to 100ms)for MlmeRadioON();

[V 0.0.1.e1]
	do not indicate connect for WPA-NONE in RTMPWPAAddKeyProc

[V 0.0.1.d9]
	sync with windows v1.0.2.0

[V 0.0.1.d8]
	fix sleep and wake connection

[V 0.0.1.d7]
	fix WPA-TKIP, AdHoc Beacon TxWI endian
	set init parameters


[V 0.0.1.d6]
[V 0.0.1.d5]
	sync to Windows - v1.0.1.0
		fix AddBAReq sequence
	
	PSK group TKIP msg2 problem, addAsicKey fail??
	

[V 0.0.1.d4]
[V 0.0.1.d3]
Shared-WEP: do not swap endian for Authen SEQ#3 for shared-wep
WPA2-PSK () - RTMPMakeRSNIE - have to do this in CntlOidRTBssidProc

[V 0.0.1.d2]
deadlock in MlmeHandler called by SetInfo
correct AID endian for PS mode
WPA2-PSK () - RTMPMakeRSNIE - have to do this in set OID_802_11_WEP_STATUS


[V 0.0.1.d1]

====================================================================================================
The base windows version
====================================================================================================
[V0.1.8.3]
1. BBP R69,R70,R73 has different value for rt2860D. So driver set different value for rt2860C/D.

[V0.1.8.2]
1. Before do scanning, set BBP R4 to 20MHz mode.
2. Let TX/RX PSDU max size limit as 16KB. (p.s : set {MAX_LEN_CFG,0x00001fff} /pAd->CommonCfg.HtCapability.HtCapParm.MaxRAmpduFactor = 1; respectively)

[V0.1.8.1]
1.change b/g protect mode ,frame gap to HT_TXOP
[V0.1.8.0]
1. release
2. Fix WiFi-dual band problems
3. Fix Adhoc problem in A band
4. Fix site survey issue when change country region
5. Fix RTS issue

[V0.1.7.0]
1. release

[V0.1.6.1]
1. Pass APSD, WMM, h+d in-house certification
2. Updat firmware v0.3, and support signal led mode
3. Fix surprise remove issue
4. Modify power save, the min current is about 24mA
5. Support legacy DLS protocol

[V0.1.6.0]
1. Improve Softap <-> Intel IOT 
2. Update some MAT register based on Jerry

[V0.1.5.6]
1. Update Led default value
2. Update WMM parameter
3. Fix check build crash issue

[V0.1.5.5]
1. Update some IOT in TGn plugfest#4.  (Stick to ShortGI(use #if WIFI_TEST), INTEL BA setup issue, MCS=32)

[V0.1.5.4]
1. Fix site survey in dual band because the scan time is too long
2. Support legacy WMM (haven't passed certification)
3. Support APSD (haven't passed certification)
4. Support 11h+d (haven't passed certification)
5. Fix driver freezed when Adhoc
6. Updat firmware v0.2, fix led issue.

[V0.1.5.3]
1. Solve IOT issue. Details in nIOT.doc.
2. PaulWu suggest spinklock in MiniportMMRequest

[V0.1.5.0]
1. Shift 802.11n OID definition that has conflict with WMM, Aggregation OID definition that was applied in rt61 after rt2860 driver coding.
2. V0.1.5.0 version driver should be used with new rt2860 GUI after 11/30.

[V0.1.4.0]
1. release

[V0.1.3.3]
1. Fix Tkip MIC fragment issue
2. Fix ZeroConfig/FunK UI with WPA2 security issue
3. Fix Adhoc Beacon Issue

[V0.1.3.2]
1. Fix fragment issue
2. Update the E2PROM reading routine for tx power per channel since we will support 40MHz in A band
3. Fix bug in auto wake routine
4. Update LED default value
5. Fix dual band issue in SoftAP
6. Update RF channel programming table to support 40MHz in A band
7. Fix Tx rate error when Adhoc with more than two clients
8. Check in firmware v0.1, this version is the first version which supports LED mode, power saving.

[V0.1.3.1]
1. Add Station connects to Pre-N only AP.
2. Rx EAP Fragment frames will fail on TKIP mode.
3. EAPOL frame will be encrypted while WPA_802_1X_PORT_SECURED.
4. Fix 2c_wlan_wep failed item.

[V0.1.3.0]
1. release

[V0.1.2.4]
1. fix surprise remove may cause infinite loop
2. fix WPA-None security issue.
3. fix counter measure issue.
4. fix DHCP frame checking on SoftAP mode.
5. fix wep encryption might fail cause by bTxkey floating.
6. fix WPA both mode security.
7. Retry to more times will cause WHQL testing failed on FailedCount checking.

[V0.1.2.3]
1. Fix adhoc basic rate in beacon
2. Fix basic rate bitmap in MAC register
3. Fix RSSI report error in UI site survey page
4. Support Hardware Radio on/off
5. Support TxPower percentage control
6. Fix TSSI read from E2PROM error
7. Fix bug, always 1Mbps when B mode

[V0.1.2.2]
1. Support RTS/CTS-to-Self
2. Fix countermeasure 
3. Fix country region issue

[V0.1.2.1]
1. Support dual band
2. Fix country region issue
3. Fix PHY issue between difference BW

[V0.1.2.0]
1. release
2. Fix some n negociation bug. [Jan - mlme.c]
3. Make initial N(Phymode) setting from registry correct. [Jan - init.c, info.c]
4. IOT with MBA more stable. (Marvel/Broadcom/Atheros) [Jan - data.c]

[V0.1.1.1]
1. NdisMIndicateStatus can't be called when driver is on halt progresss (ap.c)
2. Put WPA(#221) Element ID on the end of inside the association frame. (assoc.c)

[V0.1.1.0]
1. release

[V0.1.0.2]
1. Remove LinkDown Timer here. move it to properly place.
2. Used LinkUp Timer to indicate link up event.
3. Modify security relative codes
4. Use LinkDown Timer to indicate link down event after intiailize.
5. All security work.

[V0.1.0.1]
1. Fix MacTableInsertEntry will clear WEP Cipher if on station mode on ap.c
2. remove unnecessary code on connect.c
3. Modify RTMPAddBSSIDCipher for fixing WEP not work on rtmp.h & rtmp_info.c & sanity.c
4. Modify RTMPHandleInterrupt consider false interrupt cause by suprise remove on rtmp_man.c
5. Modify RTMPHalt on NIC exist or not in rtmp_main.c
---
6. Auto recognize Bad atheros chip , and turn on ASIC sending RTS register.
7. Add HTIOTCheck function for test, if not work, will delete in the future. 
8. IOT_STRUC structure is to store all InterOpbility action parameter.

[V0.1.0.0]
1. handle BAR control frame.
2. Periodically check BA reordering queue and refresh if possible.
3. Atheros IOT problem workaround.

[V0.0.9.4]
1. Fix countermeasure
2. Fix SoftAP WPAPSK/WPA2PSK
3. Update DRS algorithm to imporve throughput when open environment

[V0.0.9.3]
Release by Jan to fix atheros compatible issue, it should be checked in later.

[V0.0.9.2]
1. Fix Radio on/off issue, but not best power save
2. Fix NdisReset issue
3. Fix hibernate issue
4. Fix bug in RTMPMaxRssi 
5. Fix DRS issue

[V0.0.9.1]
1. Fix prefast build issue.
2. Support x64 platform
3. Rename .inf and .sys file name

[V0.0.9.0]
1. AP dynamic antenna status check
2. Modify calcuating rssi method according to Gain and RssiOffset in E2PROM
3. Modify load firmware routine about CRC check 
4. Update DRS function
5. Fix 20/40 MHz bandwidth issue

[V0.0.8.0]
[V0.0.7.1]
1. Change broadcast and mlme rate as CCK 1Mbps
2. Fix BA bugs
3. Dynamic antenna status check
4. Fix rssi report issue
5. Fix DHCP issue
6. Fix throughput issue caused by protection

[V0.0.7.0]
1. Basic MCS rate adaptation
2. MCS initial rate according RSSI
3. Update ASIC auto-fallback according to MCS table
4. Fix WindowsXP SoftAP bridge issue when AMSDU
5. Fix CCK fail issue becasue of BBP AGC
6. Update ethreal format to support rate, rssi
7. Update BBP, MAC, RF register initial value
8. Fix 20/40 MHz bandwidth issue

[V0.0.0.6]
1. RT2860c emulation ping ok


