kart okuyucu derken hocam laptopun cd yuvasına caddy takarak ssd taktım macosu da ona kurdum ordan boot ediyorum
Clover menüsü bile gelmedi hocamEkteki Clover paketini kullanarak sistemi boot etmeye çalış.
Sistemin boot olup olmaması önemli ekran kartı tanımaması v.s. sorun değil.
Evet
Launch csmyi disabled ettim clover menü geldi kendi diskimden boot etmeye tıklıyorum sadece ekranın ortasının biraz sağında çizgi çıkıyor o kadar
Yine aynı şekil çizgi çıktı hocamEkteki dosyayı indirip kullan.
AppleIntelInfo.kext v3.0 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.
Settings:
------------------------------------------
enableHWP............................... : 0
logMSRs................................. : 1
logIGPU................................. : 1
logIntelRegs............................ : 0
logCStates.............................. : 1
logIPGStyle............................. : 1
InitialTSC.............................. : 0x69f045ad7c (16 MHz)
MWAIT C-States.......................... : 270624
Processor Brandstring................... : Intel(R) Core(TM) i5-4200H CPU @ 2.80GHz
Processor Signature..................... : 0x306C3
------------------------------------------
- Family............................... : 6
- Stepping............................. : 3
- Model................................ : 0x3C (60)
Model Specific Registers (MSRs)
------------------------------------------
MSR_IA32_PLATFORM_ID..............(0x17) : 0x14000000000000
------------------------------------------
- Processor Flags...................... : 5
MSR_CORE_THREAD_COUNT.............(0x35) : 0x20004
------------------------------------------
- Core Count........................... : 2
- Thread Count......................... : 4
MSR_PLATFORM_INFO.................(0xCE) : 0x80838F3011C00
------------------------------------------
- Maximum Non-Turbo Ratio.............. : 0x1C (2800 MHz)
- Ratio Limit for Turbo Mode........... : 1 (programmable)
- TDP Limit for Turbo Mode............. : 1 (programmable)
- Low Power Mode Support............... : 0 (LMP not supported)
- Number of ConfigTDP Levels........... : 0 (only base TDP level available)
- Maximum Efficiency Ratio............. : 8
- Minimum Operating Ratio.............. : 8
MSR_PMG_CST_CONFIG_CONTROL........(0xE2) : 0x1E008405
------------------------------------------
- I/O MWAIT Redirection Enable......... : 1 (enabled, IO read of MSR(0xE4) mapped to MWAIT)
- CFG Lock............................. : 1 (MSR locked until next reset)
- C3 State Auto Demotion............... : 1 (enabled)
- C1 State Auto Demotion............... : 1 (enabled)
- C3 State Undemotion.................. : 1 (enabled)
- C1 State Undemotion.................. : 1 (enabled)
- Package C-State Auto Demotion........ : 0 (disabled/unsupported)
- Package C-State Undemotion........... : 0 (disabled/unsupported)
MSR_PMG_IO_CAPTURE_BASE...........(0xE4) : 0x21814
------------------------------------------
- LVL_2 Base Address................... : 0x1814
- C-state Range........................ : 2 (C7 is the max C-State to include)
IA32_MPERF........................(0xE7) : 0x38AFD6C83F
IA32_APERF........................(0xE8) : 0x3A3D5BD47E
MSR_FLEX_RATIO...................(0x194) : 0x0
------------------------------------------
MSR_IA32_PERF_STATUS.............(0x198) : 0x1F7600001E00
------------------------------------------
- Current Performance State Value...... : 0x1E00 (3000 MHz)
MSR_IA32_PERF_CONTROL............(0x199) : 0x2200
------------------------------------------
- Target performance State Value....... : 0x2200 (3400 MHz)
- Intel Dynamic Acceleration........... : 0 (IDA engaged)
IA32_CLOCK_MODULATION............(0x19A) : 0x0
IA32_THERM_INTERRUPT.............(0x19B) : 0x10
------------------------------------------
- High-Temperature Interrupt Enable.... : 0 (disabled)
- Low-Temperature Interrupt Enable..... : 0 (disabled)
- PROCHOT# Interrupt Enable............ : 0 (disabled)
- FORCEPR# Interrupt Enable............ : 0 (disabled)
- Critical Temperature Interrupt Enable : 1 (enabled)
- Threshold #1 Value................... : 0
- Threshold #1 Interrupt Enable........ : 0 (disabled)
- Threshold #2 Value................... : 0
- Threshold #2 Interrupt Enable........ : 0 (disabled)
- Power Limit Notification Enable...... : 0 (disabled)
IA32_THERM_STATUS................(0x19C) : 0x88220808
------------------------------------------
- Thermal Status....................... : 0
- Thermal Log.......................... : 0
- PROCHOT # or FORCEPR# event.......... : 0
- PROCHOT # or FORCEPR# log............ : 1
- Critical Temperature Status.......... : 0
- Critical Temperature log............. : 0
- Thermal Threshold #1 Status.......... : 0
- Thermal Threshold #1 log............. : 0
- Thermal Threshold #2 Status.......... : 0
- Thermal Threshold #2 log............. : 0
- Power Limitation Status.............. : 0
- Power Limitation log................. : 1
- Current Limit Status................. : 0
- Current Limit log.................... : 0
- Cross Domain Limit Status............ : 0
- Cross Domain Limit log............... : 0
- Digital Readout...................... : 34
- Resolution in Degrees Celsius........ : 1
- Reading Valid........................ : 1 (valid)
MSR_THERM2_CTL...................(0x19D) : 0x0
IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
- Fast-Strings......................... : 1 (enabled)
- FOPCODE compatibility mode Enable.... : 0
- Automatic Thermal Control Circuit.... : 1 (enabled)
- Split-lock Disable................... : 0
- Performance Monitoring............... : 1 (available)
- Bus Lock On Cache Line Splits Disable : 0
- Hardware prefetch Disable............ : 0
- Processor Event Based Sampling....... : 0 (PEBS supported)
- GV1/2 legacy Enable.................. : 0
- Enhanced Intel SpeedStep Technology.. : 1 (enabled)
- MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
- Adjacent sector prefetch Disable..... : 0
- CFG Lock............................. : 0 (MSR not locked)
- xTPR Message Disable................. : 1 (disabled)
MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x2641000
------------------------------------------
- Turbo Attenuation Units.............. : 0
- Temperature Target................... : 100
- TCC Activation Offset................ : 2
MSR_MISC_PWR_MGMT................(0x1AA) : 0x400001
------------------------------------------
- EIST Hardware Coordination........... : 1 (hardware coordination disabled)
- Energy/Performance Bias support...... : 1
- Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
- Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)
- SpeedShift Technology Enable......... : 0 (disabled)
- SpeedShift Interrupt Coordination.... : 0 (disabled)
- SpeedShift Energy Efficient Perf..... : 0 (disabled)
- SpeedShift Technology Setup for HWP.. : No (not setup for HWP)
MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x21212122
------------------------------------------
- Maximum Ratio Limit for C01.......... : 22 (3400 MHz)
- Maximum Ratio Limit for C02.......... : 21 (3300 MHz)
IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x5
------------------------------------------
- Power Policy Preference.............. : 5 (balanced performance and energy saving)
MSR_POWER_CTL....................(0x1FC) : 0x4005F
------------------------------------------
- Bi-Directional Processor Hot......... : 1 (enabled)
- C1E Enable........................... : 1 (enabled)
MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
- Power Units.......................... : 3 (1/8 Watt)
- Energy Status Units.................. : 14 (61 micro-Joules)
- Time Units .......................... : 10 (976.6 micro-Seconds)
MSR_PKG_POWER_LIMIT..............(0x610) : 0x804281D600208178
------------------------------------------
- Package Power Limit #1............... : 47 Watt
- Enable Power Limit #1................ : 1 (enabled)
- Package Clamping Limitation #1....... : 0 (disabled)
- Time Window for Power Limit #1....... : 16 (163840 milli-Seconds)
- Package Power Limit #2............... : 58 Watt
- Enable Power Limit #2................ : 1 (enabled)
- Package Clamping Limitation #2....... : 0 (disabled)
- Time Window for Power Limit #2....... : 33 (10 milli-Seconds)
- Lock................................. : 1 (MSR locked until next reset)
MSR_PKG_ENERGY_STATUS............(0x611) : 0x18D99A6
------------------------------------------
- Total Energy Consumed................ : 1590 Joules (Watt = Joules / seconds)
MSR_PP0_POWER_LIMIT..............(0x638) : 0x0
MSR_PP0_ENERGY_STATUS............(0x639) : 0xD50397
------------------------------------------
- Total Energy Consumed................ : 852 Joules (Watt = Joules / seconds)
MSR_PP0_POWER_LIMIT..............(0x638) : 0x0
MSR_PP0_ENERGY_STATUS............(0x639) : 0xD5051E
------------------------------------------
- Total Energy Consumed................ : 852 Joules (Watt = Joules / seconds)
MSR_PP1_POWER_LIMIT..............(0x640) : 0x0
MSR_PP1_ENERGY_STATUS............(0x641) : 0x30BAD
------------------------------------------
- Total Energy Consumed................ : 12 Joules (Watt = Joules / seconds)
MSR_PP1_POLICY...................(0x642) : 0x18
------------------------------------------
- Priority Level....................... : 24
MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x1C
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0x0
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0x0
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x80000000
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC3_IRTL...................(0x60a) : 0x8842
MSR_PKGC6_IRTL...................(0x60b) : 0x8873
MSR_PKGC7_IRTL...................(0x60c) : 0x8891
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1DEA8B6670
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1DEA8B6670
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0
MSR_PKG_C7_RESIDENCY.............(0x3fa) : 0x0
IA32_TSC_DEADLINE................(0x6E0) : 0x69FE8F19EA
CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency...... : 8 ( 800 MHz)
Maximum non-Turbo Ratio/Frequency....... : 28 (2800 MHz)
Maximum Turbo Ratio/Frequency........... : 34 (3400 MHz)
IGPU Info:
------------------------------------------
IGPU Current Frequency.................. : 550 MHz
IGPU Minimum Frequency.................. : 200 MHz
IGPU Maximum Non-Turbo Frequency........ : 400 MHz
IGPU Maximum Turbo Frequency............ : 1150 MHz
IGPU Maximum limit...................... : No Limit
P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (28) 29 30 ] iGPU P-States [ (11) ]
CPU C3-Cores [ 0 2 ]
CPU C6-Cores [ 1 2 3 ]
CPU C7-Cores [ 0 1 2 3 ]
CPU C3-Cores [ 0 1 2 3 ]
CPU C6-Cores [ 0 1 2 3 ]
CPU P-States [ (8) 24 28 29 30 ] iGPU P-States [ (11) ]
CPU P-States [ 8 19 24 (28) 29 30 ] iGPU P-States [ (11) ]
CPU P-States [ 8 (18) 19 24 28 29 30 ] iGPU P-States [ (11) ]
CPU P-States [ 8 18 19 21 24 (28) 29 30 ] iGPU P-States [ (11) ]
CPU P-States [ 8 (18) 19 21 24 28 29 30 31 ] iGPU P-States [ (11) ]
CPU P-States [ 8 (18) 19 21 22 24 28 29 30 31 ] iGPU P-States [ (11) ]
CPU P-States [ 8 18 19 21 22 23 24 (28) 29 30 31 ] iGPU P-States [ (11) ]
CPU P-States [ 8 18 19 21 22 23 24 28 29 30 31 (33) ] iGPU P-States [ (11) ]
CPU P-States [ 8 (18) 19 21 22 23 24 27 28 29 30 31 33 ] iGPU P-States [ (11) ]
drive.google.com
Dosyaları tekrar güncelledim tekrar deneyelim.
Evet dün bunları kurmuştum
Nasıl sileceğim hocam dosya yöneticisinden girdiğimde macos için gerekli diyor terminalde sudo ile girmeme rağmen silmiyor read only file system diyorHata almamız bundan sebep o zaman. Senden ricam o kextleri S/L/E içerisinden yedekle.ve sil sonra rebuild cache yap ve ekteki Clover ile tekrar sistemi boot etmeye çalış.
